Skip directly to site content Skip directly to page options

Inspection Detail Report

  Advanced Search |  Ship Scored 100 |  Green Sheet  |  CDC Home |  VSP Home
 
Cruise Ship: Balmoral Cruise Line: Fred Olsen Cruise Line Inspection Date: 02/04/2010 Inspection Score: 90
This cruise ship inspection report lists deficiencies found during the inspection. Additional information corresponding to each item number is available in the latest edition of the VSP Environmental Public Health Standards.

View/Print Summary Report  |  View/Print Corrective Action Statement
Item No.: 01
Site: Medical-Special Report
Violation: The vessel did not submit a special report when the passenger gastro-intestinal count reached 2% and the vessel was within 15 days of a US port.
Recommendation: The master, or designated corporate representative, of a vessel with an international itinerary destined for a U.S. port shall submit a special report at any time during a cruise, including between two U.S. ports, when: (1) The cumulative percentage of reportable cases entered in the gastrointestinal illness surveillance log, reaches 2% among passengers or 2% among crew; and (2) The vessel is within 15 days of expected arrival at a U.S. port.
Item No.: 04
Site: Potable Water-Distribution
Violation: On January 16th and 22nd, the chlorine level was below 0.1 ppm for 6 hours and 8 hours respectively.
Recommendation: Ensure that the halogenation device provides continuous halogenation of the potable water distribution system and maintains a free residual halogen between 0.2 mg/L (ppm) and 5.0 mg/L (ppm) throughout the distribution system.
Item No.: 06
Site: Potable Water-Far Point Halogen Analyzer
Violation: The far point halogen analyzer reading was 0.62 ppm. The manual reading from the vessel's colorimeter was 0.35 ppm. When asked to calibrate the machine, the ships personnel reported that the machine could not be calibrated below 0.5 ppm. The only way to calibrate the machine was to manually increase the chlorine dose from the pump in the engine room and wait until the reading steadied above 0.5 ppm.
Recommendation: Ensure that the halogen analyzer-chart recorder is properly maintained, operated, and calibrated daily in accordance with the manufacturer's instructions. Ensure that a manual comparison test is condiucted daily to verify calibration and that calibration is made whenever the manual test value is more than 0.2 ppm higher or lower than the analyzer reading.
Item No.: 08
Site: Potable Water-Far Point Halogen Analyzer
Violation: The amount of halogen injected into the potable water system was not controlled by the free halogen analyzer. The chlorine had to be increased by manually adjusting the pump.
Recommendation: Ensure that the amount of halogen injected into the potable water system is controlled by a free halogen analyzer.
Item No.: 08
Site: Potable Water-Production
Violation: On January 16th, there were eight hours between free chlorine readings during production. Also on January 18th, there were 16 hours between readings.
Recommendation: Ensure that free residual halogen monitoring is performed at least hourly during the bunkering of potable water and performed at least once every 4 hours during the onboard production of potable water.
Item No.: 08
Site: Potable Water-Cross-Connection Control Program
Violation: The air gap for the mineralizer backwash discharge was not listed in the cross-connection control program.
Recommendation: Ensure that the cross-connection control program includes at minimum: a complete listing of cross-connections and the backflow prevention method/device for each, so that there is a match to the plumbing system component and location, and an inspection frequency. Ensure that air-gaps are included in the listing.
Item No.: 08
Site: Potable Water-Cross-Connection Control Program
Violation: The air gap for the technical/laundry tank fill was not listed in the cross-connection control program.
Recommendation: Ensure that the cross-connection control program includes at minimum: a complete listing of cross-connections and the backflow prevention method/device for each, so that there is a match to the plumbing system component and location, and an inspection frequency. Ensure that air-gaps are included in the listing.
Item No.: 08
Site: Potable Water-High Saline Discharge Line
Violation: There were no shut off valves between the three way valves and the reduced pressure zone assembly backflow prevention devices for evaporator one and two.
Recommendation: Install shut off valves.
Item No.: 08
Site: Galley-Potwash
Violation: The hand spray for the potwash did not have a back flow prevention device installed.
Recommendation: Ensure that a continuous pressure-type backflow preventer is installed when a valve is located downstream from the backflow preventer.
Item No.: 08
Site: Other-Palms Dining Area
Violation: The backflow prevention device for the coffee machine in the technical space was leaking.
Recommendation: Ensure that backflow preventers are maintained in good repair.
Item No.: 16
Site: Galley-Avon & Spey
Violation: The time as a public health control plan stated that the back-up refrigerators were on time control. However, there were no back-up refrigerators in the galley. Per staff, the undercounter hot holding cabinets and the condiment station were on time control. However, these were not listed on the time control plan.
Recommendation: Ensure the time as a public health control plan reflects the operation.
Item No.: 16
Site: Galley-Room Service
Violation: There was an open canister of whipped cream without a discard label.
Recommendation: Ensure that refrigerated, ready-to-eat, potentially hazardous food: (1) Prepared on a vessel and held refrigerated for more than 24 hours is clearly marked at the time of preparation to indicate the date or day by which the food shall be consumed, which is 7 calendar days or fewer from the day the food is prepared with the day of preparation counting as day 1. (2) A container of refrigerated, ready-to-eat potentially hazardous food prepared and packaged by a food processing plant and held on the vessel after opening more than 24 hours is clearly marked, at the time the original container is opened, to indicate the date by which the food shall be consumed which is, including the day the original container is opened, 7 calendar days or fewer after the original container is opened. The day of opening is counted as day 1.
Item No.: 19
Site: Buffet-Staff Mess
Violation: There were no side sneeze shields at the hot buffet station.
Recommendation: Install side sneeze shields.
Item No.: 19
Site: Buffet-Pastry Buffet
Violation: The handles of the tongs were in contact with the pastry.
Recommendation: Ensure the handles of the tongs do not contact the food.
Item No.: 21
Site: Galley-Avon & Spey
Violation: The gasket for the ice cream chest was torn.
Recommendation: Replace the gasket.
Item No.: 21
Site: Food Service General-Equipment
Violation: Numerous pieces of galley equipment (fixed and portable) had missing fasteners, opens seams, and other difficult to clean features.
Recommendation: Ensure that nonfood-contact surfaces are free of unnecessary ledges, projections, and crevices, and designed and constructed to allow easy cleaning and to facilitate maintenance.
Item No.: 21
Site: Galley-Avon & Spey
Violation: There was an opening at the end of the metal support beam under the three compartment sink.
Recommendation: Close the opening.
Item No.: 21
Site: Galley-Avon & Spey
Violation: There was an opening around the chute of the drip pan housing for the grills.
Recommendation: Close the opening.
Item No.: 21
Site: Buffet-Waiter Stations
Violation: The laminate material on the doors and door frames was worn and damaged.
Recommendation: Ensure that nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning are constructed of a corrosion-resistant, nonabsorbent, and smooth material.
Item No.: 21
Site: Galley-Hot Galley
Violation: There were 2 aluminum foil balls used to prop up the drip pan for the flat grill.
Recommendation: Ensure that nonfood-contact surfaces of equipment and utensils are designed and constructed to be durable and to retain their characteristic qualities under normal use conditions.
Item No.: 21
Site: Buffet-Crew Mess
Violation: The beams inside the cabinet under the juice machine were made of raw, exposed wood.
Recommendation: Ensure that nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning are constructed of a corrosion-resistant, nonabsorbent, and smooth material.
Item No.: 21
Site: Galley-Bakery
Violation: The glass on the oven doors was not sealed.
Recommendation: Ensure that nonfood-contact equipment components such as doors, seals, hinges, fasteners, and kick plates are kept intact, tight, and adjusted in accordance with manufacturer's specifications.
Item No.: 24
Site: Galley-Avon & Spey
Violation: The plate surface temperature of the dishwash machine was measured at 140° F. This area was in active use.
Recommendation: In a mechanical operation, ensure that the temperature of the fresh hot water sanitizing rinse as it enters the manifold is not more than 90°C (194°F), or less than: (1) For a stationary rack, single temperature machine, 74°C (165°F); or (2) For all other machines, 82°C (180°F); or (3) A utensil surface temperature of 71°C (160°F) as measured by an irreversible registering temperature indicator shall be achieved. (4) The maximum temperature of 90°C (194°F), does not apply to the high pressure and temperature systems with wand-type, hand-held, spraying devices used for the in-place cleaning and sanitizing of equipment such as meat saws.
Item No.: 26
Site: Galley-Pantry
Violation: The water nozzles at the juice machines were soiled.
Recommendation: Ensure that food only contacts surfaces of equipment and utensils that are cleaned and sanitized.
Item No.: 27
Site: Galley-Pantry
Violation: There were dried bread crumbs inside the non-food contact areas of the slicer.
Recommendation: Ensure that nonfood-contact surfaces of equipment are kept free of an accumulation of dust, dirt, food residue, and other debris.
Item No.: 27
Site: Galley-Hot Galley
Violation: The copper pipe behind the fryer was soiled.
Recommendation: Ensure that nonfood-contact surfaces of equipment are kept free of an accumulation of dust, dirt, food residue, and other debris.
Item No.: 27
Site: Galley-Hot Galley
Violation: The space between the grills was soiled.
Recommendation: Ensure that nonfood-contact surfaces of equipment are kept free of an accumulation of dust, dirt, food residue, and other debris.
Item No.: 28
Site: Galley-Warewash
Violation: The clean utensil storage rack was next to the soiled rack and trash storage.
Recommendation: Ensure that cleaned equipment and utensils, laundered linens, and single-service and single-use articles are stored: (1) In a clean, dry location; (2) Where they are not exposed to splash, dust, or other contamination; and (3) At least 150 mm (6 inches) above the deck.
Item No.: 29
Site: Bar-Palms Bar
Violation: There was no handwash sink at this bar. The closest handwash sink was in the pantry through a door with a handle.
Recommendation: Ensure that the handwashing facility is located within 8 m (25 feet) of all parts of the area and is not located in an adjacent area that requires passage through a closed door. where the user makes hand contact with the door.
Item No.: 30
Site: Galley-Avon & Spey
Violation: The paper towel dispenser at the handwash sink near the entrance to the galley was not working. This was corrected.
Recommendation: Ensure that handwashing facilities are kept clean and in good repair.
Item No.: 33
Site: Galley-Avon & Spey
Violation: There was an opening around the bulkhead pipe penetration under the three compartment sink.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 33
Site: Galley-Avon & Spey
Violation: There was an opening around the bulkhead pipe penetration behind the combination oven.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 33
Site: Galley-Avon & Spey
Violation: There was a gap where the bulkhead tiles met the stainless steel bulkhead behind the combination oven.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 33
Site: Bar-Palms Bar
Violation: There was no coving at the deck/counter junctures.
Recommendation: Ensure that bulkhead and deck junctures are coved (including galleys, pantries, deck/counter junctures at buffets, bars, waiter stations, and dining room work counters).
Item No.: 33
Site: Food Service General-Decks
Violation: The deck tiles were damaged and there was recessed and missing deck grout in the food service areas.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 33
Site: Other-Avon & Spey Portside Waiter Station #3
Violation: There was no coving at the deck/counter juncture.
Recommendation: Ensure that bulkhead and deck junctures are coved (including galleys, pantries, deck/counter junctures at buffets, bars, waiter stations, and dining room work counters).
Item No.: 33
Site: Galley-Preparation
Violation: There was a decomposing melon on the deck under refrigerator #17.
Recommendation: Ensure that decks, bulkheads, deckheads, and attached equipment in food preparation, warewashing, pantries, and storage areas, are cleaned as often as necessary.
Item No.: 33
Site: Galley-Pantry
Violation: There was an opening around the bulkhead pipe penetration behind the coffee machine.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 33
Site: Buffet-Crew Mess
Violation: There was an opening around the deckhead pipe penetration above the juice machine.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 33
Site: Buffet-Staff Mess
Violation: There was no coving at the deck/buffet equipment and deck/juice station junctures.
Recommendation: Ensure that bulkhead and deck junctures are coved (including galleys, pantries, deck/counter junctures at buffets, bars, waiter stations, and dining room work counters).
Item No.: 33
Site: Bar-Lido Bar
Violation: There were several openings in the bulkhead of the technical spaces for the handwash station and the storage next to the technical space.
Recommendation: Ensure that decks, bulkheads, and deckheads in food preparation, warewashing, pantries, and storage areas are constructed and maintained for easy cleaning.
Item No.: 34
Site: Galley-Hot Galley
Violation: There was a leak at the supply line for the right combination oven.
Recommendation: Ensure that a plumbing system in a food area is maintained in good repair.
Item No.: 34
Site: Pantry-Palms Bar
Violation: There was a leak at the drain line behind the ice machine.
Recommendation: Ensure that a plumbing system in a food area is maintained in good repair.
Item No.: 37
Site: Galley-Warewash
Violation: There was an excessive amount of condensate on the deckhead above the clean landing of the dishwash machine.
Recommendation: Ensure that ventilation hood systems and devices are sufficient in number and capacity to prevent grease or condensation from collecting on bulkheads and deckheads.
Item No.: 37
Site: Galley-Hot Galley
Violation: There was no ventilation hood above the counter top combination oven. This will be completed in dry dock.
Recommendation: Ensure that exhaust ventilation hood systems in food preparation and warewashing areas including components such as hoods, fans, guards, and ducting are designed to prevent grease or condensation from draining or dripping onto food, equipment, utensils, linens, and single-service and single-use articles.
Item No.: 37
Site: Galley-Hot Galley
Violation: There was no ventilation hood above the counter top combination oven. This will be completed in dry dock.
Recommendation: Ensure that exhaust ventilation hood systems in food preparation and warewashing areas including components such as hoods, fans, guards, and ducting are designed to prevent grease or condensation from draining or dripping onto food, equipment, utensils, linens, and single-service and single-use articles.
Item No.: 38
Site: Galley-Avon & Spey
Violation: There was a broom stored behind the ice machine.
Recommendation: Ensure that maintenance tools such as mops, brooms, and similar items are stored in a designated locker so they do not contaminate food, food-contact surfaces of utensils, and equipment, linens, and single-service and single-use articles.
Item No.: 39
Site: Galley-Appetizer Preparation Area
Violation: There were several fruit flies in the appetizer preparation area.
Recommendation: Ensure that the presence of insects, rodents, and other pests is effectively controlled to minimize their presence in the food storage, preparation, service areas, warewashing, and utensil storage areas aboard a vessel.
*Inspections scores of 85 or lower are NOT satisfactory
Vessel Sanitation Program